A novel approach for integrating concentrated solar energy with biomass thermochemical conversion processes

Student thesis: Doctoral ThesisDoctor of Philosophy

View graph of relations Save citation


Muktar Bashir


Concentrated solar energy provides thermal energy that can be utilised for thermochemical conversion of biomass to produce liquid fuel and gases. This creates an efficient and a carbon-free process. The fast pyrolysis of biomass is an endothermic thermal process that occurs within 400-550oC at fast heating rates of >300 oC/second in the absence of oxygen. This temperature is within the range produced in a parabolic trough arrangement. The process of biomass gasification is the conversion of biomass fuels to non-condensable gases usually for chemical feedstock or as fuel using a fluidising medium. Solar intermittence is a major issue; this can be resolved by proposing a continuous process from concentrated solar energy to fuels or chemical feedstock. Computational fluid dynamics has proven to be a tool for design and optimisation of reactors. The Eulerian-Eulerian multiphase model using ANSYS Fluent has shown to be cost-effective at describing the characteristics of complex processes.

The project entails using parabolic trough for fast pyrolysis of biomass; it is integrated with a gasification process with utilities produced entirely from solar energy. The scope of the project are: (i) A Computational fluid dynamic (CFD) model analysis of the novel reactor is to be developed to model biomass pyrolysis (ii) Investigate the potentials of integrating the proposed solar reactor with a conventional circulating fluidised bed (CFB) gasifier to create a highly efficient and sustainable closed loop thermo-solar process (iii) Validate the circulating fluidised bed model with an experimental scale Circulating fluidised bed (CFB) gasifier at Aston University’s European Bioenergy Research Institute.

The report studied the use of CFD modelling to investigate fast pyrolysis of switch grass biomass using a solar parabolic trough receiver/reactor equipped with a novel gas-separation system. The separator controls the effect of tar-cracking reactions and achieves high separation efficiency compared to other gas-solid separation methods. The study assumes an average heat flux concentrated along the receiver/reactor. Pyrolysis reaction was represented as a single global first order Arrhenius type reaction with volatiles separated into condensable (bio-oil) and non-condensable products. The drying of moisture of the switch grass was represented as a mass transfer process. The separation efficiency achieved by the conical deflector was about 99%. The proposed reactor at the considered operating conditions can achieve overall energy efficiency of 42%; the product yield consist of 51.5% bio-oil, 43.7% char and 4.8% non-condensable gases. The average reactor temperature, gas residence time, and maximum devolatilisation efficiency were 450 °C, 1.5 s, and 60% respectively. There was good agreement in comparison with experimental findings from literature. A sensitivity analysis was conducted to study the effect of heat flux conditions, heat transfer, sweeping gas temperature, and particle size. The heat flux distribution showed that non-homogeneous provides a greater heating rate and temperature compared to the homogeneous flux. Radiation negligibly affects the final product composition; the radiation heats the biomass mainly rather than cause devolatilisation. The larger the biomass diameter the more bio-oil is produced, when a uniform particle temperature is assumed.

An experimental study was conducted for the validation of the hydrodynamic model of a circulating fluidised bed. The experiment measured the pressure profiles and the solid recirculation rate. The experiment result showed that particle size has a negative correlation to the ease of fluidisation. High fluidising gas flowrate has a positive impact on the fluidising regime and pressure in the riser. The following parameters were compared with experimental results: grid size, turbulence model, drag laws, wall treatment, and wall shear properties (specularity coefficient and restitution coefficient). The results proved the optimum hydrodynamic model through comparison of pressure profiles of the model with experimental results.

The gasification of char in a circulating fluidised was studied using the optimum hydrodynamic model validated from experiment. The model considered the effect of turbulence on the species evolution and tar reforming with char. Over the range of operating conditions, the results looked into the hydrodynamics and product yield of the gasifier. The product yields obtained for the base case was CO (12%), CO2 (19%), H2 (6%), CH4 (0.7%), and N2 (63%). The results proved that for smaller particles the evolution of species are dominated by kinetics. The catalytic effect of char showed improvement in tar yield and CGE to 15.12g/Nm3 and 67.74%. The product yields showed improvement with the compositions of CO2 and H2 due to reforming reactions. The yields and efficiency were in qualitative agreement with results from literature. The proposed models described will provide details on the procedures for future design of integrated solar biomass thermochemical conversion systems.


Original languageEnglish
Awarding Institution
Award dateMar 2017


  • computational fluid dynamics, solar thermochemical conversion, solar pyrolysis, biomass fast pyrolysis, char gasification, circulating fluidised bed reactor

If you have discovered material in the Aston Research Explorer, which is unlawful e.g. breaches copyright, (either theirs or that of a third party) or any other law, including but not limited to those relating to patent, trademark, confidentiality, data protection, obscenity, defamation, libel, then please read our Takedown Policy and contact the service immediately.

Download statistics

No data available

Employable Graduates; Exploitable Research

Copy the text from this field...